STEP 1: PREP, PREP, PREP!
First, prep your piece of furniture. You can’t just slap on a coat of paint and call it a day. It will peel and chip and it will not last. The first thing I like to do before I paint a piece is to give it a good cleaning (after removing the hardware, of course), especially if it’s been sitting around in a dusty garage or storage space. Murphy’s Oil Soap works great and it’s safe for furniture. Remove all drawers before painting and work on those separately.
STEP 2: SAND
Next, sand your furniture and get all of the glossy finish off so that the paint will have a good surface to “grab” onto. Medium-grit sandpaper should be fine. (I use fine-grit between paint coats.) If you are painting as opposed to staining, there is no need to strip the finish or sand it down to the bare wood. Simply removing the glossy finish will suffice. If the surface is already dull, you can skip this step.
STEP 3: PRIME
After your furniture is dry and dust-free, paint on some primer. This helps your paint adhere to the piece better and it also covers any stains or discolorations in the wood. I prefer KILZ Primer, and they also offer it in a spray (which I haven’t tried yet, but plan to!). I’ve heard great things about it. Oil-based primer is also great for furniture
STEP 4: SAND AGAIN
Then, sand again! Using a fine-grit sandpaper, lightly sand your piece between EVERY SINGLE coat of paint. This helps you attain a much more professional and even finish. Be sure to remove the sanding dust each time—tack cloth works great.
STEP 5: PAINT
Now that you have your piece primed and ready, it’s time to paint. For furniture, I use interior latex paint, usually in a semi-gloss finish. I recommend anything that’s not a flat finish. (It will show every fingerprint and flaw and will be harder to clean.) The glossier the finish, the easier to clean. Paint thin coats, and I will repeat: sand between each coat! This step is very important if you want to achieve an even finish. I normally paint 2-3 coats total.
Now, there are a few different ways to go about painting. You can use a paint sprayer, or even regular spray paint (just get a decent brand!), a brush, or roller. I usually use a small foam roller on the main parts of the furniture and a brush in the hard to reach crevices, painting the crevices first. The roller helps prevent visible brush strokes.
TEP 6: PROTECT
After your last coat of paint has dried for at least 24 hours, you are ready to seal it. (Or you can just leave it alone and let it cure for about 30 days. But if you plan on doing this, then seriously, leave it alone and don’t touch it!) Sealing your furniture provides extra protection for your finish and also creates a wipeable, easy to clean surface. If you are using a white or extremely light color of paint, I highly recommend that you do NOT use polyurethane to seal your finish. It can yellow over time. On any other paint color, it should be fine, and I recommend Minwax Wipe-On Poly because it is extremely easy to use. (I like the Satin finish.) I really prefer to use a water-based topcoat though like Minwax Polycrylic. It’s easier to clean up and there aren’t as many fumes.
Another option, which I love, that can be used on any color including whites, is furniture wax. Minwax Finishing Wax is awesome, and I’ve heard good things about other brands as well. You just wipe it on (I use cheesecloth to apply it), let it dry for 10-15 minutes, and then buff it with a clean cloth until you get it as shiny as you want it. This is what I used on my dresser. After you’ve sealed your furniture, I recommend leaving it alone for a day or two before using it or touching it. It would be a shame to cause damage to all of that hard work by handling it too soon!
Add your hardware, and you’re done! You can also distress the piece if you’d like, or just leave it as is. The dresser in the photo was just slightly distressed using fine grit sandpaper. I distressed it after my last coat of paint and before applying my wax.